banner



How To Fix The Power Button On Hp Pavilion 15 Laptop

Z7_3054ICK0KGTE30AQO5O3KA30N0

Removing and replacing the ability button board for HP OMEN xv Notebook PC

This document applies to HP OMEN 15 Notebook computers.

HP OMEN 15 Notebook PC

Before y'all begin

  • Have a Phillips-head screwdriver, tweezers or needle-nose pliers, and a not-marring flat-bladed tool, or similar prying tool.

  • Turn off the computer. Disconnect the Ethernet or modem cablevision. Disconnect the power cord.

  • Transfer the figurer to a clear, flat, stable work surface over a not-carpeted floor.

  • HP strongly recommends the use of an anti-static wrist strap and a conductive foam pad when working on the computer.

  • Do not remove a component from its protective packaging until you are ready to install it.

alarm:

Earlier starting, power off the reckoner and expect for components to cool earlier starting these procedures.

caution:

This production contains components that tin be damaged by electrostatic discharge (ESD). To reduce the chance of ESD damage, piece of work over a not-carpeted floor, utilise a static dissipative work surface (such as a conductive cream pad), and wear an ESD wrist strap connected to a grounded surface.

caution:

Procedures in this certificate are provided by HP for qualified service agents and as a courtesy to its customers. Servicing internal components increases the adventure of damaging the computer which might non exist covered nether warranty. Understand the gamble and refer to the product's warranty before attempting to service the figurer.

Video overview

View the following video earlier using the steps in this commodity.

annotation:

The video and graphics in this commodity depict a specific configuration of the notebook. The same removal and replacement procedures apply to all configurations of the notebook.

Removing the power button board

Follow the steps in this section to remove the ability button lath.

warning:

Make sure the calculator is disconnected from power before starting.

Step i

Remove the base enclosure.

note:

For instructions on removing the base of operations enclosure, see the HP back up document Removing and replacing the base of operations enclosure for HP OMEN 15 Notebook PC.

Removing the base enclosure

Footstep 2

Remove the battery.

notation:

For instructions on removing the battery, see the HP support document Removing and replacing the battery for HP OMEN 15 Notebook PC.

Removing the battery

Step three

Remove the heat sink assembly

note:

For instructions on removing the oestrus sink assembly, meet the HP support certificate Removing and replacing the oestrus sink assembly for HP OMEN 15 Notebook PC.

Removing the heat sink assembly

Step four

Using minimal strength, lift the locking bar upwardly on the power push board ZIF connector...

Lifting the locking bar up

...and disconnect the power push lath ribbon cablevision from the organisation lath.

Disconnecting the power button board ribbon cable

Pace 5

Using a non-marring prying tool, remove the power button board ribbon cablevision from the adhesive that secures it to the top cover.

Removing the power button board ribbon cable from the adhesive on the top cover

Step 6

Using a Phillips-head screwdriver, remove the screw that secures the ability button board to the elevation cover.

Removing the screw

Pace vii

Lift the ability button board off of the alignment pins on the pinnacle cover.

Lifting the power button board off of the alignment pins

Step viii

Identify the power button lath into a static dissipative handbag.

Placing the power button board into a static dissipative bag

Replacing the power push board

Use the steps in this department to replace the power push lath.

Step ane

Remove the power button board from the static dissipative pocketbook.

Removing the power button board from the static dissipative bag

Step 2

Place the power button board onto the alignment pins on the top cover.

Placing the power button board onto the alignment pins

Step 3

Using a Phillips-caput screwdriver, supercede the screw that secures the power button board to the acme cover.

Replacing the screw

Step four

Using tweezers or a pair of needle-nose pliers, insert the power button board ribbon cable into the power push button lath ZIF connector on the system board...

Inserting the power button board ribbon cable into the ZIF connector

...and press the locking bar down to lock the cable into place.

Pressing down the locking bar

Step 5

Employ pressure to the length of the power push button board ribbon cable to adhere it to the height cover.

Applying pressure to the power button board ribbon cable to adhere it to the top cover

Step six

Supplant the heat sink associates.

note:

For instructions on replacing the estrus sink assembly, come across the HP support document Removing and replacing the heat sink assembly for HP OMEN xv Notebook PC.

Replacing the heat sink assembly

Step seven

Supplant the battery.

note:

For instructions on replacing the battery, see the HP back up document Removing and replacing the battery for HP OMEN 15 Notebook PC.

Replacing the battery

Step 8

Replace the base enclosure.

For instructions on replacing the base of operations enclosure, see the HP support certificate Removing and replacing the base enclosure for HP OMEN 15 Notebook PC.

Replacing the base enclosure

How To Fix The Power Button On Hp Pavilion 15 Laptop,

Source: https://support.hp.com/us-en/document/c04510832

Posted by: moorehicave.blogspot.com

0 Response to "How To Fix The Power Button On Hp Pavilion 15 Laptop"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel